NEW!
ready-made masses for the application of rust and patinaAMAZING DECORATIVE EFFECT!




MCS RC and MCS PC are ideal for creating unique and special applications on walls in apartments, offices or industrial buildings. The result will certainly satisfy even the most demanding users.
By using a specialized composition based on natural metals, the obtained effects are very realistic.
THIS IS A REAL RUST AND A TRUE PATINE
Effect intensity is controllable due to the use of MCS RA and MCS PA activators. We apply them to the finished coating with the help of an atomizer, brush or sponge, thus allowing the effect activity to be adjusted. It is also possible to use the activator pointwise – this will allow any shaping of the surface of the occurrence of rust or patina.
MCS RC and MCS PC match perfectly with finishes made of natural materials such as wood, metal, glass, bricks. They bring a bit of austerity and industriality to the interior. MCS RC and MCS PC, however, are above all infinite arrangement possibilities.
ground preparation

preparation of concrete substrate
The concrete substrate should be stable and adequately bearable.
Permissible humidity of the substrate must not exceed 4%.
It should be removed mechanically by grinding or grinding all kinds of dirt and old protective coatings. Add cavities to the epoxy resin. For weaker substrates, use a deeply penetrating epoxy resin.
To avoid any problems with the adhesion of microcement to the substrate, it is recommended to use the MCS Quartz Contact strainer.
ATTENTION: Cracks and voids should be repaired before making the main floor.

preparation of the substrate from OSB boards and wood-based materials
Furniture panels, OSB and other furniture materials should be prepared by primed surfaces in a similar way as during the preparation of concrete substrate. In this case, we simply omit the application of deep penetrating resin. OSB boards should be sanded in order to remove the top impregnating layer on their surface

preparation of walls and other vertical surfaces
The surface should be thoroughly vacuumed from all kinds of dust, dirt and debris.
In order to avoid weak MCS RC adhesion problems, it is recommended to use the MCS Quartz Contact strainer.

adhesion layer
MCS Quartz Contact is a ready-to-use product. Before use, mix the contents of the package until a homogeneous mass is obtained. Apply MCS Quartz Contact application using a brush or roller. Depending on the ambient temperature, let it dry for 4-7 hours.
NOTE: the ambient temperature during the work should be less than + 5 ° C and greater than + 30 ° C.
APPLICATION

MCS RC is applied by hand, steel floats of various width and length. It should be applied with fast, strong movements – circular or longitudinal. After placing the layer around 1 m2, use the MCS RA activator to force the rust effect. Before applying the applicator, the surfaces immediately adjacent to the MCS RC layer must be protected.
NOTE: do not allow the layer to dry completely before applying the applicator. No rust effect can be achieved on the dried layer.
Put the applicator on the surface using an atomizer (included in the kit, brush or sponge) It is important to ensure that the MCS RA activator application is even and uniform for the whole surface, in order to obtain a better rust effect, you can additionally apply MCS RA pointwise. places.
During work and after finishing, ventilate the rooms until the odor disappears. In case of lack of ventilation or insufficient efficiency, individual respiratory protection should be used.
IMPREGNATION

Impregnation is carried out using a spray primer to close the layer (after applying the primer, additional painting is possible). Dried coatings should be sprayed with varnish and allowed to dry.
first microcement in poland
for spray
guns
EASY APPLICATION
Now you are able to reach with the microcement coating where it was previously impossible. The ideal coating is always the same thickness.
FASTER RENOVATION
Now the time needed for the renovation will be significantly shortened. Where the renovation required two days of work – now only one is enough.
effect
Classic microcement

MCS hydro

mcs walls and floors
mcs furniture
the best renovation system
You can spread the micro-cement layer on tiles, panels, wood, tiles, concrete, and walls made of cardboard panels. It also works perfectly as an additional layer on bathroom fixtures, window sills, kitchen countertops or furniture. Thanks to it, we can get an industrial and austere look, reminiscent of classic concrete, but with the difference that the system proposed by us is dust-free. It is worth remembering that (MCS) MICRO CEMENT SOLUTION can be used not only on walls, floor, furniture or other elements inside the room.

shades of concrete

ADDITIONAL COLORS

varnish for concrete monovar pu
Monovar PU is a modern, one-component, waterborne (low VOC content) colorless polyurethane varnish with very high scratch and abrasion resistance. Does not contain isocyanates, so it is safe when used, also when spraying. The varnish is very hard, dries quickly (only 2 hours to touch) and has excellent resistance to moisture and UV radiation. It does not turn yellow and does not change the color of the substrate *. It creates an easy-to-clean, easy to clean, aesthetic finish without streaks.


hydrograff HP concrete varnish
Hydrograff HP is a high-strength, two-component, waterborne and non-yellowing polyurethane varnish with a low VOC content. The varnish is characterized by very high mechanical and chemical resistance, surpassing many solvent systems. Provides a colorless finish and perfect floor appearance for a long service life.
APPLICATION EXAMPLES

SYSTEM APPLICATION






TECHNICAL DATA
[table id=3 /]
PREPARATION OF SUBSTRATE
[table id=4 /]